Brocade FastIron Ethernet Switch Platform and Layer 2 Swit Uživatelský manuál stáhnout pdf (Strana 167)

maintain aggregate links over multiple port. LACP PDUs are exchanged between ports on each device

to determine if the connection is still active. The LAG then shuts down any port whose connection is no

longer active.

NOTE

ICL LAGs only support static trunks.

Syntax: [no] lag lag-name [ { static | dynamic } [ id number ] ]

To configure an ICL static LAG, enter the following commands.

device-1(config)# lag MCT_lag1 static id 2

Brocade-1(config-lag-MCT_lag1)# ports ethernet 1/7 to 1/8

Brocade-1(config-lag-MCT_lag1)# primary-port 1/7

Brocade-1(config-lag-MCT_lag1)# deploy

Step 2: Configure the MCT VLAN, MCT session VLAN, and recommended MCT keep-

alive VLAN

To create the MCT session VLAN and recommended MCT keep-alive VLAN for Brocade-1 in the

topology of Figure 31 on page 165, enter the following commands.

device-1(config)# vlan 3001 name MCT-keep-alive

device-1(config-vlan-3001)# tagged ethernet 1/9

device-1(config-vlan-3001)# exit

device-1(config)# vlan 3000 name Session-VLAN

device-1(config-vlan-3000)# tagged ether 1/7 to 1/8

device-1(config-vlan-3000)# no spanning-tree

For routers, add the following commands.

device-1(config-vlan-3000)# router-interface ve 3000

device-1(config)# interface ve 3000

device-1(config-vif-3000)# ip address 10.1.1.3/24

For switches, add the following commands.

device-1(config)# ip address 10.1.1.3/24

To create a session VLAN and keep-alive VLAN for device-2, enter the following commands.

device-2(config)# vlan 3001 name MCT-keep-alive

device-2(config-vlan-3001)# tagged ethernet 2/10

device-2(config-vlan-3001)# exit

device-2(config)# vlan 3000 name Session-VLAN

device-2(config-vlan-3000)# tagged ether 2/5 to 2/6

device-2(config-vlan-3000)# no spanning-tree

For routers, add the following commands.

device-2(config-vlan-3000)# router-interface ve 3000

device-2(config)#interface ve 3000

device-2(config-vif-3000)# ip address 10.1.1.2/24

For switches, add the following commands.

device-2(config)# ip address 10.1.1.2/24

To implicitly configure the MCT VLAN and add the ICL as a tagged member of the VLAN, enter the

following commands.

device-1(config)# vlan 1000 name MCT-VLAN-example

device-1(config-vlan-1000)# tagged ether 1/15 to 1/16 e 1/7 to 1/8

Step 2: Configure the MCT VLAN, MCT session VLAN, and recommended MCT keep-alive VLAN

FastIron Ethernet Switch Platform and Layer 2 Switching Configuration Guide 167

53-1003086-04

1 2 ... 162 163 164 165 166 167 168 169 170 171 172 ... 453 454

Komentáře k této Příručce

Žádné komentáře

Brocade FastIron Ethernet Switch Platform and Layer 2 Swit Uživatelský manuál Strana 167

Komentáře k této Příručce

Související produkty a manuály pro Počítačové příslušenství Brocade FastIron Ethernet Switch Platform and Layer 2 Swit